ASE A4 Steering Suspension Practice Test

11. Technician A says the Z in P225/60R16 89Z indicates the tire's speed rating. Technician B says different sized tires on the rear of a vehicle will illuminate the yellow ABS warning light. Who is correct?

  • A. Technician A
  • B. Technician B
  • C. Both A and B
  • D. Neither A or B

11.

Answer A is wrong. The last letter is the speed rating. A (Z) rated tire indicates that the tire is capable of 149 mph.

Answer B is wrong. Different sized tires on the rear of a vehicle affect the ABS braking system. Because of the difference in tire size, the wheels spin at different speeds. This can result in the amber ABS warning light.

Answer C is correct. Both technicians are correct.

Answer D is wrong. A (W) rated tire is rated at 168 mph, and the (Y) found on high-performance cars, an incredible 186 mph.

NextRead more...

12. A vehicle's steering wheel does not return to center after completing a turn. Which of the following is MOST likely causing this condition?

  • A. A loose inner tie rod end.
  • B. A binding ball joint.
  • C. A loose outer tie rod end.
  • D. Worn stabilizer bar bushings.

12.

Answer A is wrong. Loose tie rod ends result in vehicle wander, feathered tire wear, and a popping or clunking sound while turning the steering wheel.

Answer B is correct. A binding ball joint will affect the steering wheel's ability to return to the center. It will also result in a clunking noise while turning the steering wheel.

Answer C is wrong. Check for binding (not loose) tie rod ends, idler arm, and other steering linkages. If something is binding in the column, linkage, or gearbox, the steering wheel's return to the center will be affected.

Answer D is wrong. Worn stabilizer bushings affect vehicle sway while turning. Steering wheel returnability depends on the caster angle, and most vehicles incorporate a positive caster (~ 6° ) into both front wheels.

NextRead more...
Automotive suspension components.

13. Component A in the illustration above:

  • A. Is part of the vehicle’s shock absorbing system.
  • B. Absorbs impact as a vehicle travels over potholes and bumps in the road.
  • C. Can be found on both front and rear suspension systems.
  • D. All of the above.

13.

Answer A is wrong. All of these choices are correct about jounce bumpers. Answer D is correct.

Answer B is wrong. Jounce bumpers and bump stops absorb impact, saving passengers and suspension components from the sudden jolt.

Answer C is wrong. They are on the front and rear suspension systems.

Answer D is correct. All of these answers are correct.

NextRead more...

14. A vehicle with power steering requires increased effort to steer. A power steering pressure test gauge is installed to test the power steering system's flow and pressure. To measure power steering pump pressure:

  • A. Close the shutoff valve for 5 seconds.
  • B. Open the shutoff valve and hold the steering wheel against its stop for 5 seconds.
  • C. Close the shutoff valve for 30 seconds.
  • D. Open the shutoff valve and record the reading at 1000 RPM and 3000 RPM.

14.

Answer A is correct. With the gauge connected, close the shutoff valve for 5 seconds and compare it with the manufacturer's specifications. If the reading is not within specifications, the power steering pump is faulty.

Answer B is wrong. To check the gear housing for leaks, hold the steering wheel against its stop and check fluid pressure against specifications. Do not hold the wheel in this position for long. Power steering systems reach pressures above 1000 lbs per square inch.

Answer C is wrong. Never hold the shutoff valve closed for more than 5 seconds unless instructed by the manufacturer. It causes the fluid to overheat, possibly damaging the power steering pump, pressure hoses, and seals.

Answer D is wrong. Check the flow control valve's operation with the shutoff valve in the open position and record the reading at 1000 RPM and 3000 RPM. Compare these two readings against specifications.

NextRead more...

15. After adjustments are made, the technician measures the worm shaft bearing preload and sector shaft lash of a recirculating ball steering gear. The technician should use:

  • A. An outside micrometer.
  • B. An inch-pound torque wrench.
  • C. A dial gauge.
  • D. A foot-pound torque wrench.

15.

Answer A is wrong. This adjustment will affect steering wheel free play. If under-adjusted, the steering wheel will feel loose and sloppy.

Answer B is correct. Measure worm bearing preload and sector lash with an inch-pound torque wrench. Worm bearing preload and sector gear mesh are adjustments for recirculating ball steering gears.

Answer C is wrong. Recirculating ball gearboxes are found on parallelogram steering linkage systems.

Answer D is wrong. Always check other items like the steering shaft u-joints and couplings, loose mounting bolts, or steering linkage before making any steering gear adjustments.

NextRead more...